make case depth more clear

Author: mariusandra

cases/case1.scad

@@ -7,15 +7,20 @@ view_mode="print_vertical"; // [print_vertical, print_horizontal, stacked, explo
 // Shrinkage adjustment when printing vertically. By default 0.4mm of shrinkage for every 100mm of print height.
 vertical_print_scale = 1.004;
 
+/* [Case depth] */
+
+panel_cover_depth = 1.6; // Panel cover thickness
+panel_depth  = 1.2; // Thickness of the eInk panel as measured
+case_depth = 10.0; // Total inside compartment thickness
+back_depth = 1.2; // Back plate thickness 
+fillet_radius = 2.5; // How round to make the case. Not used with thick borders.
+
 /* [Panel dimensions] */
 
-// Physical width of the eInk panel (mm)
-panel_width  = 284.49;
-// Physical height of the eInk panel (mm)
-panel_height = 208.81;
+panel_width  = 284.49; // Physical width of the eInk panel (mm)
+panel_height = 208.81; // Physical height of the eInk panel (mm)
 
-// Clearance around the eInk panel (mm)
-clearance = 0.3;
+clearance = 0.3; // Clearance around the eInk panel (mm)
 
 // Dimensions of the bezel on the eInk panel. This part will be covered by the panel cover.
 panel_bezel_left   = 11.7;
@@ -37,23 +42,6 @@ case_inner_padding_right = 4;
 case_inner_padding_top = 4;
 case_inner_padding_bottom = 4;
 
-/* [Case dimensions] */
-
-// How round to make the case. Disabled if thick_border=true
-fillet_radius = 2.5;
-
-// Panel cover thickness
-panel_cover_depth = 1.6;
-
-// Thickness of the eInk panel as measured
-panel_depth  = 1.2;
-
-// Total inside compartment thickness
-case_depth = 10.0;
-
-// Back plate thickness 
-back_depth = 1.2;
-
 /* [Thick border] */
 thick_border = false;
 thick_border_width = 12.0;
@@ -89,20 +77,16 @@ screw_offset_right  = 5.0;
 screw_offset_top    = 5.0;
 screw_offset_bottom = 5.0;
 
-// Extra screws on the top side (0.0 to 1.0)
-extra_screws_top = [0.48, 0.52, 0, 0, 0]; // [0.0:0.05:1.0]
-// Extra screws on the bottom side (0.0 to 1.0)
-extra_screws_bottom = [0.48, 0.52, 0, 0, 0]; // [0.0:0.05:1.0]
-// Extra screws on the left side (0.0 to 1.0)
-extra_screws_left = [0, 0, 0, 0, 0]; // [0.0:0.05:1.0]
-// Extra screws on the right side (0.0 to 1.0)
-extra_screws_right = [0.5, 0, 0, 0, 0]; // [0.0:0.05:1.0]
+extra_screws_top = [0.48, 0.52, 0, 0, 0]; // Extra screws on the top (0.0 to 1.0)
+extra_screws_bottom = [0.48, 0.52, 0, 0, 0]; // Extra screws on the bottom (0.0 to 1.0)
+extra_screws_left = [0, 0, 0, 0, 0]; // Extra screws on the left (0.0 to 1.0)
+extra_screws_right = [0.5, 0, 0, 0, 0]; // Extra screws on the right (0.0 to 1.0)
 
-// Hole made into layer 1.2
+// Hole made into panel cover
 panel_screw_insert_diameter = 3.45;
 panel_screw_insert_depth = 2.0;
 
-// Cylindrical hole inserted into layers 2.1 and 2.2
+// Cylindrical hole inserted into case
 case_screw_hole_diameter        = 4.5;
 case_screw_hole_thread_diameter = 2.0; // Hole for the screw thread that goes all the way through
 case_screw_hole_floor_depth     = 1.0; // Depth of the floor of the screw hole

cases/pimoroni.13in3.spectra.12mm.scad

@@ -7,8 +7,9 @@ view_mode="print_horizontal"; // [print_vertical, print_horizontal, stacked, sta
 /* [Case depth] */
 panel_cover_depth = 1.6;
 panel_depth  = 3.0;
-case_depth = 12.0; // pi zero 12mm; board imposed minimum 5.5mm;
+case_depth = 12.0; // with pi zero 12mm; board minimum 5.5mm;
 back_depth = 1.2;
+fillet_radius = 2.5; // How round to make the case. Not used with thick borders.
 
 /* [Panel dimensions] */
 panel_width  = 297.0;

cases/pimoroni.13in3.spectra.6mm.scad

@@ -7,8 +7,9 @@ view_mode="print_horizontal"; // [print_vertical, print_horizontal, stacked, sta
 /* [Case depth] */
 panel_cover_depth = 1.6;
 panel_depth  = 3.0;
-case_depth = 6.0; // pi zero 12mm; board imposed minimum 5.5mm;
+case_depth = 6.0; // with pi zero 12mm; board minimum 5.5mm;
 back_depth = 1.2;
+fillet_radius = 2.5; // How round to make the case. Not used with thick borders.
 
 /* [Panel dimensions] */
 panel_width  = 297.0;

cases/pimoroni.7in3.spectra.12mm.scad

@@ -7,8 +7,9 @@ view_mode="print_horizontal"; // [print_vertical, print_horizontal, stacked, sta
 /* [Case depth] */
 panel_cover_depth = 1.6;
 panel_depth  = 3.0;
-case_depth = 12.0; // pi zero 12mm; board imposed minimum 5mm;
+case_depth = 12.0; // with pi zero 12mm; board minimum 5mm;
 back_depth = 1.2;
+fillet_radius = 2.5; // How round to make the case. Not used with thick borders.
 
 /* [Panel dimensions] */
 panel_width  = 174.0;

cases/waveshare.10in3.scad

@@ -5,7 +5,11 @@ include <case1.scad>;
 view_mode="print_horizontal"; // [print_vertical, print_horizontal, stacked, stacked_case, exploded, only_case, only_thick_border, only_panel_cover]
 
 /* [Case depth] */
-case_depth = 10.0;
+panel_cover_depth = 1.6;
+panel_depth  = 1.2;
+case_depth = 10.0; // change this for your usecase
+back_depth = 1.2;
+fillet_radius = 2.5; // How round to make the case. Not used with thick borders.
 
 /* [Panel dimensions] */
 panel_width  = 216.70;

cases/waveshare.13in3e.scad

@@ -5,7 +5,11 @@ include <case1.scad>;
 view_mode="print_horizontal"; // [print_vertical, print_horizontal, stacked, stacked_case, exploded, only_case, only_thick_border, only_panel_cover]
 
 /* [Case depth] */
-case_depth = 6.0;
+panel_cover_depth = 1.6;
+panel_depth  = 1.2;
+case_depth = 9.0; // change this for your usecase
+back_depth = 1.2;
+fillet_radius = 2.5; // How round to make the case. Not used with thick borders.
 
 /* [Panel dimensions] */
 panel_width  = 285.09;
@@ -22,10 +26,13 @@ panel_border_right  = 7.5;
 panel_border_top    = 16.1;
 panel_border_bottom = 16.1;
 
+case_inner_padding_left = 4;
 case_inner_padding_right = 6;
+case_inner_padding_top = 4;
+case_inner_padding_bottom = 4;
 
 /* [Thick border] */
-thick_border = false;
+thick_border = true;
 thick_border_width = 12.0;
 thick_border_extra_depth = 15.0;
 

cases/waveshare.4in01f.desk.scad

@@ -5,12 +5,15 @@ include <case1.scad>;
 view_mode="print_horizontal"; // [print_vertical, print_horizontal, stacked, stacked_case, exploded, only_case, only_thick_border, only_panel_cover]
 
 /* [Case depth] */
+panel_cover_depth = 1.6;
+panel_depth  = 6.8;
 case_depth = 6.0;
+back_depth = 1.2;
+fillet_radius = 2.5; // How round to make the case. Not used with thick borders.
 
 /* [Panel dimensions] */
 panel_width  = 69.7;
 panel_height = 98.3;
-panel_depth  = 6.8;
 
 panel_bezel_left   = 10.5;
 panel_bezel_right  = 6.5;

cases/waveshare.4in0e.desk.scad

@@ -5,12 +5,15 @@ include <case1.scad>;
 view_mode="print_horizontal"; // [print_vertical, print_horizontal, stacked, stacked_case, exploded, only_case, only_thick_border, only_panel_cover]
 
 /* [Case depth] */
+panel_cover_depth = 1.6;
+panel_depth  = 6.8;
 case_depth = 6.0;
+back_depth = 1.2;
+fillet_radius = 2.5; // How round to make the case. Not used with thick borders.
 
 /* [Panel dimensions] */
 panel_width  = 67.8;
 panel_height = 101.0;
-panel_depth  = 6.8;
 
 panel_bezel_left   = 6.2;
 panel_bezel_right  = 6.2;

cases/waveshare.7in3e.scad

@@ -5,7 +5,10 @@ include <case1.scad>;
 view_mode="print_horizontal"; // [print_vertical, print_horizontal, stacked, stacked_case, exploded, only_case, only_thick_border, only_panel_cover]
 
 /* [Case depth] */
-case_depth = 6.0;
+panel_cover_depth = 1.6;
+panel_depth  = 1.2;
+case_depth = 6.0; // change this for your usecase
+back_depth = 1.2;
 fillet_radius = 2.2;
 
 /* [Panel dimensions] */

cases/waveshare.7in5.scad

@@ -5,7 +5,11 @@ include <case1.scad>;
 view_mode="print_horizontal"; // [print_vertical, print_horizontal, stacked, stacked_case, exploded, only_case, only_thick_border, only_panel_cover]
 
 /* [Case depth] */
-case_depth = 6.0;
+panel_cover_depth = 1.6;
+panel_depth  = 1.2;
+case_depth = 6.0; // change this for your usecase
+back_depth = 1.2;
+fillet_radius = 2.5; // How round to make the case. Not used with thick borders.
 
 /* [Panel dimensions] */
 panel_width  = 170.3;