✨ PLR_HEAT_BED_ON_REBOOT

MarlinFirmware/Marlin#26691

Author: thinkyhead

config/default/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/3DMatik/XL/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/ADIMLab/Gantry v1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             28 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/ADIMLab/Gantry v2/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Alfawise/U20-bltouch/Configuration_adv.h

@@ -1804,6 +1804,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Alfawise/U20/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AliExpress/CL-260/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/A2/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.