Board ZFC39, Fan speed controller

[PSLLSP]

Hi Thomas,

just FYI, new board ZFC39 with STM8S003 micro-controller. It can control up to three PC PWM fans.

http://www.ebay.com/itm/PC-CPU-12V-4-Wire-Fan-Temperature-Control-PWM-Speed-Control-Module-W-Alarm/282460745283?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

http://www.formfactors.org/developer/specs/4_wire_pwm_spec.pdf

BTW, I am sorry for new issue but there is no contact email noted.

[TG9541]

Hi PSLLSP,

Opening an issue is good way for submitting a feature request. Thanks for including the fan specs.
Do you own such a board? If yes, did you trace how the STM8S pins are used?

[PSLLSP]

Hi Thomas,

I have a sample board. There is 78L05 regulator on the board and STM8S003F (TSSOP20) MCU.

MCU is connected in this way:

1 (BEEP) - 150R - 1uF - BUZZ - GND
2 (AIN) - 1k - 50k NTC - GND; 10k pull-up to VCC (10k - 50k NTC is voltage divider)
3 (IN) - DP5 (label BF2)
4 (NRST) - 100nF - GND; there is a pad connected to NRST at the bottom of the PCB.
5 (IN) - DP4 (label BF1)
6 (IN) - DP3 (label TP2)
7 (VSS) - GND
8 (VCAP) - 1uF - GND
9 (VDD) - VCC (+5V); there is a pad connected to VDD at the bottom of the PCB.
10 (IN) - 150R - FAN2-3 (RPM); signal is filtered by pull-up 10k and pull-down 470pF
11 (IN) - NC ??
12 (OUT) - red LED - 10k - VCC
13 (OUT) - 150R - FAN3-4 (PWM)
14 (AIN) - trimmer 10k F3; signal is filtered by pull-down 100nF; voltage divider between VCC and GND
15 (IN) - DP2 (label TP1)
16 (OUT) - 150R - FAN2-4 (PWM)
17 (OUT) - 150R - FAN1-4 (PWM)
18 (IN/SWIM) - DP1 (label TFL)
19 (AIN) - trimmer 10k F2; signal is filtered by pull-down 100nF; voltage divider between VCC and GND
20 (IN) - 150R - FAN1-3 (RPM); signal is filtered by pull-up 10k and pull-down 470pF

NOTE, RPM signal from FAN3 is not connected to MCU (no feedback from FAN3, no detection of blocked fan)
NOTE, DPx switches connect signals to GND
NOTE, buzzer has to be actively driven by MCU, it is not self oscillating type
NOTE, NTC is NTC50K3950 (label on PCB)

images of PCB can be found on internet, one example:
https://images-na.ssl-images-amazon.com/images/I/51Pn9NLqUlL.jpg

Video on YouTube: https://www.youtube.com/watch?v=ZldI9R1zOGE

[TG9541]

OK, looks good: it's easy to get a console (e.g. PD1 "SWIMCOM", or PD1/PD6). Retrofitting the FAN3 RPM input isn't hard, and I think that the trimmer inputs can be converted into additional temperature sensor inputs.

I've ordered one of those boards. If you'd like to start experimenting: you can flash the SWIMCOM image to the board, and start some experiments:

• getting it to produce PWM signals takes some Forth words
• a simple stall detection would be easy (several options, e.g. pin change interrupts, T2 capture)
• if you want to actually measure, let alone closed-loop-control, the RPM, writing simple pin-change interrupt handlers is maybe the easiest option.
• Functional dependencies (temperature to RPM, time to RPM) can be done easily with interpolation code here.

[TG9541]

I now have a board, still no fans, though :-)

[PSLLSP]

Just note about new board. "DC-DC adjustable Power supply module with LCD display", that can be ordered for about 4USD is build around STM8S003K3T6 MCU. This MCU is in LQFP32 package and is hidden under LCD. I see 4 holes on PCB those could be SWIM interface. I see MP2307, LM358, HT7133-1 (3.3V LDO voltage regulator), two buttons, one induktor and several rezistors, capacitors and diodes. LCD has back-light.

http://www.ebay.com/itm/DC-DC-Adjustable-Step-down-Power-Supply-Module-Voltage-Current-LCD-Display-Shell-/142218535015?hash=item211ce2a067:g:WIMAAOSw2xRYWQNf

https://www.youtube.com/watch?v=tskURZyHbhk
https://www.youtube.com/watch?v=N_H4sVyhIaU

[TG9541]

Thanks, ordered one. Do you know how they controlled the LCD?

[PSLLSP]

I don't know HW details. It could be a challange to write firmware for this board. Some ideas how to drive LCD display could be found here:

http://www.atmel.com/Images/doc2569.pdf
http://www.ti.com/lit/an/slaa516a/slaa516a.pdf
http://www.st.com/content/ccc/resource/technical/document/user_manual/ca/6a/61/13/08/c4/48/f9/CD00278045.pdf/files/CD00278045.pdf/jcr:content/translations/en.CD00278045.pdf

[TG9541]

Thanks for the links! I'll be looking into how LCD control works in the power supply once it's there.

[TG9541]

Since the LCD hides the µC I'll have to disassemble the board I have. A second device is now in the mail. Help with reverse-engineering would be appreciated.

[TG9541]

Just in the case: if anybody would like to see some progress on this board, just drop me a note here. It shouldn't be too hard to program a fan control application on it provided that your requirements are known!

[berrydejager]

Does anyone know if it is possible to make the temperature ranges lower?
Let's say, while TP1/TP2=OFF/OFF, the lowest accelerating at 25℃ and Full speed at 35℃

TP1 | TP2 | Accelerating temperature | Full speed temperature
-- | -- | -- | --
OFF | OFF | 35℃ | 45℃
ON | OFF | 40℃ | 55℃
OFF | ON | 50℃ | 70℃
ON | ON | 60℃ | 90℃

[TG9541]

Hi @berrydejager, I have no knowledge of the code that defines the behavior of the ZFC39 as-is but you can, of course, program the µC on the board to any temperature to fan speed ratio. Right now my time to do programming and testing is a bit scarce, but I'd be happy to help.